• ™ NetworX Series NX-6V2 Control Panel Installation and Startup Downloaded from: • GE Security, Gladewater, Texas, USA. This document contains proprietary information of GE Security, USA and is furnished to its customer solely to assist that customer in the installation, testing, operations, and/or maintenance of the equipment described. Vampire The Masquerade Character Sheet Program.

This document shall not be reproduced in whole or in part nor shall its contents be disclosed to any third party without the written approval of GE Security. • Table of Contents GENERAL DESCRIPTION..... 4 ORDERING INFORMATION....4 III.

BOARD INSTALLATION..... 4 NX-6V2 WIRING DIAGRAM....5 TERMINAL DESCRIPTIONS....6 NETWORX KEYPAD MAXIMUM WIRE RUN...6 PROGRAMMING THE LED KEYPADS....7 KEYPAD ADDRESS AND PARTITION.... 7 CHANGING USER CODES.... • GENERAL DESCRIPTION The NetworX NX-6V2 represents a new approach to security systems design. Drawing on our experience in the world market as the largest exporter of USA manufactured controls, we have developed the most flexible, durable, and user-friendly control ever seen in our industry. • WIRING DIAGRAM NX-6V2 Control.

• TERMINAL DESCRIPTIONS TERMINAL DESCRIPTION House Telephone Ring (Grey). Telephone Ring (Red). Telephone Tip (Green). House Telephone Tip (Brown). EARTH Earth Ground. Connect to a cold water pipe or a 6 to 10 foot driven rod.

Connect to a 16.5V 40 or 50 VA Class ll U.L. Approved transformer. If used as a siren output (default), the speaker rating should be 15 watt at 8 or 16 ohm, or 30/40 watt at 4, 8, or 16 ohms. • PROGRAMMING THE LED KEYPADS KEYPAD ADDRESS AND PARTITION This section describes how to program the address and partition of each keypad as well as the options that are available. The address of the keypad is important because this is how the panel supervises the keypads. The factory default for the Master code is [1]-[2]-[3]-[4] when using a 4-digit code or [1]-[2]-[3]-[4]-[5]-[6] for a 6-digit code.

Ge NetworX NX-6V2 Pdf User Manuals. View online or download Ge NetworX NX-6V2 User Manual.

• ASSIGNING AUTHORITY LEVEL: • Enter [r]-[6]-[master code]. The 'Ready' LED will flash. • Enter the 2 digit user number. The 'Ready' LED will illuminate steady and the 'Instant' LED will flash. • Refer to the chart below for the description of each LED.

Turn the LED on for the features that you desire. ATTRIBUTES IF LED 8 IS OFF ATTRIBUTES IF LED 8 IS ON Reserved. • the [MEDICAL] key. To review the data in a location, repeat the above procedure, pressing [r] without any numeric data entry. Each time [r] is pressed, the programming data of the next segment will be displayed for review. EXITING A LOCATION After the last segment of a location is programmed, pressing [r] will exit that location, turn the 'Ready'. • PROGRAMMING EXAMPLES FIGURE1 (Numerical Data) Zone 1 LED = 1 Zone 2 LED = 2 Data = 9 Data = 66 Zone 4 LED = 8 Zone 7 LED = 64 To change data in a Pressing [#] will exit a segment, enter the location without data followed by [ ].

• LOADING FACTORY DEFAULTS To load the factory defaults, enter the program mode using the procedure on page 8, then type [9]-[1]-[0]-[#]. The keypad will beep 3 times indicating that the loading is in progress. The loading takes about 6 seconds. ENROLLING MODULES AND KEYPADS For supervision purposes, the NX-6V2 has the ability to automatically find and store in its memory, the presence of all keypads, zone expanders, wireless receivers, and any other module connected to the data terminal. • DIAL ATTEMPTS/BACKUP CONTROL FOR PHONE 1 2.

Numerical Segment 1- Dial attempts: Location 3, Segment 1 is used to enter the number of dial attempts (1 to 15 Attempts) the communicator will make to Phone 1 before ending the notification process. Factory default is '8' and the communicator will make eight (8) attempts to the first number. • COMMUNICATOR FORMAT FOR PHONE 2 1. Numerical Location 8 contains the communicator format used to transmit to the receiver connected to Phone 2. Consult the instruction manual for your central station receiver to determine which format is compatible, and select from Table XII-1 COMMUNICATOR FORMAT SELECTIONS on page 11. • ACCOUNT CODE FOR PHONE 3 6. Numerical The account code sent when Phone 3 is dialed is programmed in location 13.